基于模型定义的复合材料旁路挤压试验压缩夹具参数化设计
作者:
作者单位:

1.中国商用飞机有限责任公司北京民用飞机技术研究中心结构完整性研究部,北京 102211;2.中国商飞北京民用飞机技术研究中心民用飞机结构与复合材料北京市重点实验室,北京 102211;3.北京航空航天大学,北京 100191

作者简介:

李晨,1989年出生,博士,工程师,主要从事复合材料、先进合金、仿真模拟、智能制造等方面的研究工作。E-mail:lichen2@comac.cc

通讯作者:

中图分类号:

TH12

基金项目:


Parametric Design of Compression Fixture for Composite Materials Bypass Interaction Test According to Model Based Definition
Author:
Affiliation:

1.COMAC Beijing Aircraft Technology Research Institute, Structural Integrity Department, Beijing 10221;2.COMAC Beijing Aircraft Technology Research Institute, Beijing Key Laboratory of Civil Aircraft Structures and Composite Materials, Beijing 102211;3.Beihang Unversity, Beijing 102211

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    针对民用飞机复合材料许用值试验开展中需要设计大量构型类似而繁杂的试验夹具,为提高夹具设计的效率和准确性、促进设计的标准化,本文总结了ASTM标准中复合材料旁路挤压试验的压缩试验夹具构型设计和制造等相关信息,采用包含基于模型的定义(Model Based Definition, MBD)信息的CATIA二次开发方法,提出了一个复合材料旁路挤压试验夹具参数化设计方法,实现了含设计制造信息的试验夹具装配体模型的快速准确建立。结果表明:含设计制造信息的试验夹具装配体设计的关键尺寸链参数为试验件孔径D和试验件宽度W。采用本文方法参数化设计的试验夹具符合ASTM关于复合材料许用值试验标准规定的夹具设计准确性和标准化的要求并缩短了设计周期。

    Abstract:

    In order to improve the efficiency and accuracy of fixture design and to promote the standardization of design, this paper summarizes the design and manufacture of compression test fixture for composite bypass compression test in ASTM standard. The CATIA secondary development method including Model Based Definition (MBD) information is employed. A parametric design method of composite by-pass compression test fixture is proposed. This realizes the rapid and accurate establishment of assembly model of test fixture with design and manufacturing information. The results show that the key dimension chain parameters of the test fixture assembly with design and manufacturing information are the diameter D and width W of the test piece. The test fixture designed by this study meets the requirements of accuracy and standardization of fixture design related to allowable value test standard for composite materials specified in ASTM and it shortens the design cycle.

    参考文献
    相似文献
    引证文献
引用本文

李晨,陈程,金沙亮,高丽敏.基于模型定义的复合材料旁路挤压试验压缩夹具参数化设计[J].宇航材料工艺,2021,51(1):25-31.

复制
分享
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2020-05-12
  • 最后修改日期:2020-12-20
  • 录用日期:2020-06-26
  • 在线发布日期: 2021-02-19
  • 出版日期: 2021-02-28
第十一届航天复合材料成形与加工工艺技术中心交流会 征文通知

关闭